Thank you!
Lisätietoja siitä, miten Epson käsittelee henkilökohtaisia tietojasi, saat lukemalla tietosuojalausuntomme.
Lähetä yhteystietosi alla, niin Epsonin asiantuntija ottaa yhteyttä:
Lisätietoja siitä, miten Epson käsittelee henkilökohtaisia tietojasi, saat lukemalla tietosuojalausuntomme.
The videos in this article will guide you through some of the frequently asked questions about the Epson SureColor SC-S series printers.
Select your product range from the tabs below
Expand the section related to your question:
SureColor SC-S30600 |
00:01Loading Media
0:10 0Wait until [Load media.] appears on the screen.
0:40 While holding the tabs of each media holding plate on both sides,
0:48 move both media holding plates to the right and left sides of the platen respectively.
1:27 Make sure the holder handle shaft is visible.
1:38 If not,
1:42 rotate the handle forward until it stops.
2:01 If the right and left edges of the roll media are uneven, rewind the media to align the edges before loading it.
2:10 Check how the media is rolled; (A) printable side out
2:14 or (B) printable side in.
2:18 Place media on the roll supports according to how the media is rolled.
2:27 Align the left edge of the media with the set position on the label.
3:08 To ensure the roll holder is inserted into the roll core sufficiently, push the side of the roll holder towards the roll end twice.
3:27 Rotate the handle until part A is fully inserted.
3:40 Once part A is hidden, do not turn the handle any further.
3:45 Check the right and left edges, and if they are not aligned, realign them.
3:54 Insert the end of media approximately 30 cm into the opening.
4:08 Confirm the left edge of the media is positioned in the middle of the label.
4:45 Hold the center of the media with one hand, and
4:51 pull the media to the middle of the after heater.
5:01 Do not pull the media with both hands.
5:11 This label is not used when loading media.
5:28 While holding the tabs of the media holding plate on both sides,
5:33 move it to the right side of the media.
5:39 Position the media holding plate so that the edge of the media is aligned to the middle of the three round holes.
5:50 Move it to the left side of the media.
5:56 Position the media holding plate so that the edge of the media is aligned to the middle of the three round holes.
For a full written guide please click here and locate the Loading Media (SC-S30600 series) section of the guide.
SureColor SC-S50600 | |
SureColor SC-S70600 |
0:01 Loading Media
0:10 Wait until [Load media.] appears on the screen.
0:41 While holding the tabs of each media holding plate on both sides,
0:49 move both media holding plates to the right and left sides of the platen respectively.
1:29 Make sure the holder handle shaft is visible.
1:39 If not,
2:04 If the right and left edges of the roll media are uneven, rewind the media to align the edges before loading it.
2:18 or (B) printable side in.
2:31 According to the media width, align the left edge of the media with the set position on the label.
2:53 Make sure the right edge of the media is aligned within one of the squares according to the media width.
3:34 To ensure the roll holder is inserted into the roll core sufficiently, push the side of the roll holder towards the roll end twice.
3:53 Rotate the handle until part A is fully inserted.
4:06 Once part A is hidden, do not turn the handle any further.
4:11 Check the right and left edges, and if they are not aligned, realign them.
4:22 Insert the end of media approximately 30 cm into the opening.
4:42 Check that both the right and left edges of the media pass within the dimensions of the square that was adjusted earlier.
5:05 Hold the center of the media with one hand, and
5:10 pull the media to the middle of the after heater.
5:24 Do not pull the media with both hands.
5:33 This label is not used when loading media.
5:45 Set the low pressure rollers (A) to the set positions.
5:55 High pressure rollers (B) are not used here.
6:06 Move pressure rollers while pressing them down.
6:20 Move the high pressure rollers fully to the ends because they are not used here.
6:32 Position the low pressure rollers on both ends within 5 mm from the left and right edges of the media.
6:48 Position the remaining low pressure rollers within the black square labels.
7:00 There may be unnecessary low pressure rollers depending on the media width.
7:04 Position the unnecessary low pressure rollers away from the black square labels.
7:15 When transparent/milky white film is loaded or during ink layering, position the high pressure rollers within 10 mm from the left and right edges of the media.
7:28 Position the low pressure rollers away from the black square labels because they are not used here.
7:47 While holding the tabs of the media holding plate on both sides,
7:53 move it to the right side of the media.
7:57 Position the media holding plate so that the edge of the media is aligned to the middle of the three round holes.
8:09 Move it to the left side of the media.
8:14 Position the media holding plate so that the edge of the media is aligned to the middle of the three round holes.
SureColor SC-S30600 | |
SureColor SC-S50600 | |
SureColor SC-S70600 |
0:01 Using the Auto Take-up Reel Unit
0:06 Press and hold the DOWN button to feed the media as far as the roll core holder.
0:37 Align the roll core holder with the right edge of the media.
0:51 Leaving approximately 10 to 20 cm in the center of the media,
0:55 cut off the left and right corners 25 cm or more from the corners.
1:06 Slide the holder in until part A is fully inserted.
1:11 Stop when part A is no longer visible.
1:21 Cut paper tape into a 60 cm strip, and paste it on the center of the media using adhesive tape.
1:32 Press and hold the UP button to rewind the media until the end of the paper tape becomes level with the pipe.
1:44 Take-up with the Printed Side Facing Out
1:49 Put the paper tape to the rear side of the roll core and paste the tape there with adhesive tape.
2:01 Flip the Auto switch toward you.
2:11 Press and hold the DOWN button, and
2:14 feed media until both ends of the media reaches the roll core and then it is wrapped once or twice around the roll core.
2:30 Move the guides until they slightly touch both edges of the media.
2:40 When using banners, attach three each counterweights on both ends of the tensioner.
2:46 Take-up with the Printed Side Facing In
2:51 Pass the paper tape behind the roll core and pull it out toward you, and then paste the tape there with adhesive tape.
SureColor SC-S30600 | |
SureColor SC-S50600 | |
SureColor SC-S70600 |
0:01 Cleaning when the nozzles are clogged frequently
0:07 Select [Head Maintenance] on the Maintenance menu.
0:25 The print head is positioned for maintenance.
0:34 Entire Wiper (Once a Week)
0:47 SC-S30600 Series Remove the wiper when cleaning it.
0:57 SC-S70600 Series/SC-S50600 Series Clean both of them.
1:04 Hold the wiper by the attachment point and remove it.
1:23 Dampen a clean-room wiper with ink cleaner,
1:33 wipe off any adhered ink, lint, and dust.
1:44 With the cleaning stick dampened with ink cleaner,
1:49 wipe off any adhered ink on the bottom of the wiper.
2:15 Wipe off with the cleaning stick dampened with ink cleaner.
2:37 Press down until you hear a click.
2:45 Cleaning the guide part of caps and removing lint
2:56 When lint or dust has adhered to the inside of the cap,
3:03 remove it using the tip of a cleaning stick or tweezers.
3:19 When ink has adhered,
3:23 wipe off with the cleaning stick dampened with ink cleaner.
3:57 Press the [OK] button.
4:09 Press the [OK] button.
SureColor SC-S30600 | |
SureColor SC-S50600 | |
SureColor SC-S70600 |
0:01 Daily Cleaning
0:06 What You’ll Need
0:11 Cleaning Around the Print Head
0:16 Select [Head Maintenance] on the Maintenance menu.
0:31 The print head is positioned for maintenance.
0:52 Clean the print head.
1:05 SC-S30600 Series
1:08 SC-S70600 Series/SC-S50600 Series
1:12 Wipe off any adhered ink stains from the parts around the Print Head.
1:23 Clean the rear side and the slits on both sides carefully.
1:54 To the area on the illustration, apply ink cleaner with a cleaning stick ...
1:58 ... to dissolve adhered ink stains.
2:12 Dampen a new clean-room wiper with ink cleaner and wipe away any dust and dirt on the cleaning wiper.
2:37 Wipe away ink stains.
2:46 Don't move the cleaning wiper back and forth.
2:51 Keep cleaning until dried and adhered ink, lint, and dust are cleanly removed.
2:58 Wipe stains off the cleaning wiper, and store it in a location away from direct sunlight.
3:17 Cleaning Around Caps and the Wiper (rubber part)
3:36 SC-S30600 Series Clean the wiper (rubber part).
3:39 SC-S70600 Series/SC-S50600 Series Clean both of them.
3:43 Clean the front and back of the wiper.
3:48 SC-S30600 Series Clean the caps.
3:52 SC-S70600 Series/SC-S50600 Series Clean both of them.
3:55 Wipe off adhered ink, lint, and dust on the edges of all the caps.
4:04 Clean the outer peripheries of all the caps.
4:27 Cleaning the Wiper Cleaner
4:32 Press the [OK] button and the wiper moves to the back.
4:38 SC-S30600 Series Clean the wiper cleaner.
4:41 SC-S70600 Series/SC-S50600 Series Clean both of them.
4:47 Grasp the cleaner as shown and lift it from the printer.
4:49 Turn the wiper cleaner upside down and check if any lint or dust adhered to the bottom surface.
4:56 Remove lint or dust if any using tweezers.
5:02 SC-S30600 Series Attach the wiper cleaner.
5:06 SC-S70600 Series/SC-S50600 Series Attach both of them.
5:11 Press down until you hear a click.
5:20 Press the [OK] button.
5:25 If a notice dialog appears with a beep during cleaning,
5:32 press the [OK] button and keep on cleaning.
5:37 The notice dialog will reappear if you are still cleaning 10 minutes from then.
Expand the section related to your question:
For a full written guide please click here and locate the Loading Media section of the guide.
For a full written guide please click here and locate the Loading Media section of the guide.
For a full written guide please click here and locate the Auto Take-up Reel section of the guide.
For a full written guide please click here and locate the Auto Take-up Reel section of the guide.
For a full written guide please click here and locate the cutting media section of the guide.
For a full written guide please click here and locate the maintenance section of the guide.
On lisätty ostoskoriin