Thank you!
Lisätietoja siitä, miten Epson käsittelee henkilökohtaisia tietojasi, saat lukemalla tietosuojalausuntomme.
Lähetä yhteystietosi alla, niin Epsonin asiantuntija ottaa yhteyttä:
Lisätietoja siitä, miten Epson käsittelee henkilökohtaisia tietojasi, saat lukemalla tietosuojalausuntomme.
The videos in this article will guide you through some of the frequently asked questions about the Epson SureColor SC-F9200.
Expand the section related to your question:
0:01 Loading Media
0:09 Wait until [Load media.] appears on the screen.
0:36 While holding the tabs of each media holding plate on both sides,
0:43 move both media holding plates to the right and left sides of the platen respectively.
1:30 Make sure the holder handle shaft is visible.
1:39 If not,
1:42 rotate the handle forward until it stops.
1:57 Check how the media is rolled; (A) printable side out
2:01 or (B) printable side in.
2:05 Place media on the roll supports according to how the media is rolled.
2:14 Align the left edge of the media with the set position on the label.
2:53 To ensure the roll holder is inserted into the roll core sufficiently, push the side of the roll holder towards the roll end twice.
3:12 Rotate the handle until part A is fully inserted.
3:24 Once part A is hidden, do not turn the handle any further.
3:29 Check the right and left edges, and if they are not aligned, realign them.
3:41 Insert the end of media approximately 30 cm into the opening.
4:02 Confirm the left edge of the media is positioned in the middle of the label.
4:29 Hold the center of the media and raise the media loading lever.
4:37 Pull the media straight forward to the leading edge of the after heater.
4:59 To rewind the media, press and hold the DOWN button (for Printable Side In media) or UP button (for Printable Side Out media).
5:04 Rewind the media until the leading edge comes to the point indicated with the red line.
5:31 While holding the tabs of the media holding plate on both sides,
5:35 move it to the right side of the media.
5:38 Position the media holding plate so that the edge of the media is aligned to the middle of the three round holes.
5:53 Move it to the left side of the media.
5:57 Position the media holding plate so that the edge of the media is aligned to the middle of the three round holes.
0:01 Using the Auto Take-up Reel Unit
0:08 Make sure the Auto switch is set to off.
0:13 Press and hold the DOWN button to feed the media as far as the point indicated with the blue line.
0:45 Make sure the holder handle shaft is visible.
0:53 If not,
0:56 Rotate the handle backward until it stops.
1:11 Align the roll core holder with the right edge of the media.
1:45 Push the roll core holder twice towards the roll end.
2:01 Rotate the handle until part A is fully inserted.
2:16 Once part A is hidden, do not turn the handle any further.
2:19 Take-up with the Printed Side Facing In
2:25 In the order as shown, tape the leading edge of the media to the roll core.
2:30 Pass the media behind the core then toward you.
2:42 Attach the media using adhesive tape while pulling the center of the media straight.
2:55 Tape the media while pulling it.
3:11 If the media is lifted up, add more pieces of tape.
3:17 Press and hold the DOWN button until enough media for a single wrap around the roll core is fed.
3:28 Make sure the Auto switch is set to off.
3:32 Flip and hold the Manual switch to the back side to wind the media around the roll core.
3:42 Make sure the media is attached without looseness.
3:45 Make sure the edges of media taken up on the roll core are not misaligned.
3:48 Flip the Auto switch to the back side.
3:54 Take-up with the Printed Side Facing Out
3:59 In the order as shown, tape the leading edge of the media to the roll core.
4:04 Attach the media using adhesive tape while pulling the center of the media straight.
4:13 Tape the media while pulling it.
4:36 If the media is lifted up, add more pieces of tape.
4:42 Press and hold the DOWN button until enough media for a single wrap around the roll core is fed.
4:50 Make sure the Auto switch is set to off.
4:53 Flip and hold the Manual switch to the front side to wind the media around the roll core.
5:06 Make sure the media is attached without looseness.
5:08 Make sure the edges of media taken up on the roll core are not misaligned.
5:13 Flip the Auto switch to the front side.
0:01 Cleaning when the nozzles are clogged frequently
0:01 Cleaning (Print head/Wiper/Cap)
0:06 What You’ll Need
0:11 Cleaning Around the Print Head
0:10 Select [Head Maintenance] on the Maintenance menu.
0:36 The print head is positioned for maintenance.
0:47 Soak a new cleaning stick (wide) in ink cleaner.
1:04 Open the maintenance cover and clean the print head.
1:23 Wipe off adhered ink, lint and dust attached around the print head.
1:39 Clean the rear side and the slits on both sides carefully.
2:24 Do not touch the enclosed areas, or print quality may decline.
2:34 To the area on the illustration, apply ink cleaner with a cleaning stick …
2:39 ... to dissolve adhered ink stains.
3:06 Soak the cleaning stick (wide) in ink cleaner, then wipe away any dust and dirt on the front, back, and sides of the wiper blade.
3:41 Wipe away ink stains.
3:51 Don't move the cleaning wiper back and forth.
3:56 Keep cleaning until dried and adhered ink, lint, and dust are cleanly removed.
4:05 Wipe stains off the cleaning wiper, and store it in a location away from direct sunlight.
4:33 Cleaning of the Wiper and its Socket
4:54 Hold the wiper by the tab and remove it.
5:07 Soak a new cleaning stick (wide) in ink cleaner.
5:22 Clean the front and back of the wiper with the cleaning stick (wide).
5:40 Clean the bottom of the wiper with the cleaning stick (wide).
5:54 Clean the socket of the wiper with the cleaning stick (wide).
6:16 Press down until you hear a click.
6:23 Cleaning of the Caps
6:29 Soak a new cleaning stick (narrow) in ink cleaner.
6:51 Wipe off any ink attached inside the anti-drying caps with the cleaning stick (narrow).
7:12 Never touch the insides of the suction caps.
7:24 Hold the cleaning stick perpendicularly and wipe the outer areas of all the caps.
7:39 Wipe off ink attached in the guide sections.
7:53 Wipe off the ink cleaner attached inside the anti-drying caps with a new cleaning stick (narrow).
8:06 Wipe them until ink cleaner dries up.
8:13 Never touch the insides of the suction caps.
8:29 Press the [OK] button twice.
On lisätty ostoskoriin